Cast aluminum cylinder combustion chamber for the Zenoah G260PUM engine.

Round aluminum cylinder that travels up and down in the cylinder for the Zenoah G260PUM engine.

Adjustable split metal ring that fits around a piston and seals the gap between the piston and the cylinder wall for the Zenoah G260PUM engine.

Cast aluminum cylinder combustion chamber for the Zenoah G231PUM engine.

Round aluminum cylinder that travels up and down in the cylinder for the Zenoah G231PUM engine.

Adjustable split metal ring that fits around a piston and seals the gap between the piston and the cylinder wall for the Zenoah G231PUM engine.

Includes coil, plug cap & spring. Takes the electronic pulses created by the red source coil and produces power to drive the spark plug, allowing ignition

Creates electric energy from a magnetic pickup located on the flywheel

This covers the plug wire and spring from the Grey Ignition Coil - creates a air-tight connection over the spark plug

This small clip retains the wrist pin in the piston

Made from steel, this is a basic baffle-type muffler - both quiet and economical

Quality aluminum standard cooling jacket - includes brass fittings. Available in your choice of seven anodized colors.

Large "O" ring that works in either stock or "Very Cool" Water Jackets for Zenoah water-cooled engines.

Small "O" ring that works in either stock or "Very Cool" Water Jackets for Zenoah water-cooled engines.

An original cast aluminum lower case set - sold with seals, bolts and gaskets. Bearings (pair) optional

A steel shaft with lobes and a pin which holds the connecting rod to the piston - transfers the power of the piston movement through a rotational force which supplies the engine's output.

Precision bearing race that supports the crank shaft inside the engine lower case halves. Sold as a pair.

Precision bearing race that supports the crank shaft inside the engine lower case halves.

Precision bearing race that supports the crank shaft inside the engine lower case halves.

A steel shaft with lobes and a pin which holds the connecting rod to the piston - transfers the power of the piston movement through a rotational force which supplies the engine's output.

Goes between the carburetor and the engine. This is the part of the engine that is drilled and tapped for use with a clutch/water pump.

*Using a water pump? Make sure to have us drill/tap this block for only $5! *

Flexible cable that connects the throttle servo in the radio box to the engine's carburetor, producing smooth throttle.

14" standard, 18" long
Specify for which carb

Fits all Zenoah 23cc and 26cc engines (Car, airplane, boat, helicoptor, etc...) as well as other brands and size engines. Primer bulb allows for easy starting. Comes standard on G260/G231 engines

Features a larger intake volume over the stock 644 carb, providing more fuel & air, translating to more horsepower! Works on many other engines besides those listed as well

Independent tunable high & low speed jets. Has an accelerator pump built-in & primer bulb. Most carbs have limited pumping pressure at 1/2 or full throttle. Has increased pumping pressure & smoother response.

Click to learn more

Everything you need to rebuild the Walbro carburetor. Includes all necessary gaskets, diaphragms, filters and other small pieces. Does not include needles.

Includes bolts and spacers necessary for installation.

Available in anodized colors, it is used to lock the piston in place - allowing you to loosen and tighten collet bolts and flywheels.

Formed composite material that seals the lower two case halves (crank case).

Formed composite material that seals the carb and the insulator block

Formed composite material that seals between the bottom of the cylinder and the top of the cases

Formed composite material that seals the case and the exhaust pipe

Formed composite material that seals between the insulator block and the cylinder

5-piece set includes carb gasket, cylinder base gasket, case gasket, exhaust gasket and insulator gasket

Pin that attaches one end of a connecting rod to the piston. Not for the G231PUM.

Bearing race that supports the wrist pin in the center of the piston and the connecting rod

Cap-type washer that is placed on each end of the wrist pin bearing as a spacer

Pin that attaches one end of a connecting rod to the piston. Not for the G260PUM.

Upgrade your standard Zenoah engine washers/screws/etc. with our all-new stainless steel kit!
Click to view diagram

Insterted into the head of an internal combustion engine cylinder that ignites the fuel mixture by means of an electrode.

Plastic piece is the replacable ring inside recoil assembly which engages onto the recoil pulley.

More commonly known as the pull starter, this is the piece that is used to fire up/start your Zenoah engine.

This piece locks the flywheel in place and is the positive engagement connection for the recoil starter on your engine.

Functions as magnetic pickup for coil. Along with red source coil, creates energy to make the spark. It acts as a flywheel to help improve idle and smooths transitions between low and high.

This little piece locks the flywheel (rotor) to the crank shaft.

Zenoah tool that was designed for easy removal of flywheel on Zenoah marine engines

Just five (5) ounces of BONZÍBreak-In Oil to one gallon of gas allows for complete engine break-in. Developed with your Zenoah marine engine in mind.

(1) 10 oz. bottle
Use for 2 complete break-ins.

We STRONGLY RECOMMEND for your new Zenoah engine!